Legacy Models Power Point Baseboard Dowels (2-Pairs) By DCC Concepts | Code: LM-PP.2 | Any Scale
We guarantee the price of our forthcoming releases for Locomotives, coaches and wagons to be at least 10-25% less than the RRP at the time of release. We also offer large discounts on many of our railway accessory ranges. We continually monitor other retailers to ensure that our prices are always competitive. Please note limited editions and exclusive products are not included in the price promise offer.
Have one to sell? Sell it to Rails of Sheffield
You purchased this item on
|Product category||Tools ,|
|Product scale||Any Scale|
Wire-Free Baseboard connections
Easily installed, super-accurate alignment dowels that remove the need for wires!
PowerPoint dowels are a dream come true. Highly accurate, they can both transmit track power and perfectly align your baseboards. All of the electrial parts are gold plated too, so they'll never fail you!
PowerPoints can confortably handle far more power than a DCC system can deliver, so you will only need to use one pair to reliably transfer power between average baseboards.
Work carefully and you will obtain a great result when installing your new Legacy PowerPoint Dowels
- Clamp the baseboard ends together. Be sure the top surfaces are perfectly level and aligned. (You can temporarily screw an offcut of wood over the top of joint to ensure it is perfect)
- Mark the position for the dowels. Drill a pilot hole right through both ends using a 3mm drill. (keep it at 90 degrees to the board faces as this step will guide all subsequent drilling)
- Separate the two boards. Use a 19mm spade drill bit, and go just deep enough into the front face of each board end (2mm) (This is about right to allow the flange of the dowel to sit flush with the baseboard ends)
- Now, using a 13mm spade drill bit and working from the other side, drill right through the board. You will now have a 13mm hole with a 19mm flange. (Clean it up and remove anu rough edges and sawdust to make it ready for the Dowell installation)
- Add a little PVA to the grooves in each dowel & insert it flush with the face of the board.
- (If it’s too tight for a firm push-fit, ream the hole with sandpaper. Do NOT tap them in as you may damage them)
- To secure boards together after alignment, drill clearance holes for 1/4” bolts & wingnuts. (They do not need to be tight as the dowels will do all the work of aligning the boards perfectly)
- Connect the track power wires.
- Your PowerPoints are now installed and ready! By the way...PowerPoints will carry more than 5 amps of track power, so you will not overload them - ever!.
- Only top quality materials are used. The electrical parts are all gold plated so they will never tarnish and lose conductivity. PowerPoints can also be disassembled for cleaning or lubrication if needed, and we even supply you with spare parts in the pack. They really ARE designed to last forever!
- Mitre Cutter
- Countersunk Screws 1.5 x 8mm (60 Pieces)
- Countersunk Screw Set 8x Vials with 60 screws in each
- Fibreglass Brush Fine
- Fine Sprue Cutter
- Fine Wire Strippers (Pre-Settable)
- Countersunk Screws 2 x 6mm (60 Pieces)
- Pan Head Screws 1 x 3mm (60 Pieces)
- Fibreglass Brush Medium
- Super Sharp Shears
- Countersunk Screws 2 x 8mm (60 Pieces)
- Pan Head Screws 1 x 5mm (60 Pieces)
- Pan Head Screws 1 x 8mm (60 Pieces)
- Fibreglass Brush Refills Fine (5 Pack)
- Fibreglass Brush Refills Medium (5 Pack)
- Nut Driver Set
- Legacy Models Power Point Baseboard Dowels (4 Pairs)
- Pan Head Screws 1.5 x 4mm (60 Pieces)
- File Set (6 Files)
- Compound Protractor (Plastic)
- Screw and Nut Driver Set
- Baseboard Dowels (2) with Spade Drill Bits
- Pan Head Screws 1.5 x 6mm (60 Pieces)
- Sapphire No Clean Flux (30ml)
- Baseboard Dowels (4)
- Pan Head Screws 1.5 x 8mm (60 Pieces)
- Track Cutters (Super Sharp)
- Pan Head Screws 2 x 5mm (60 Pieces)
- Iron Stand (w/Sponge)
- Drill Bits (Coated) 0.3mm – 1.6mm (20 Pack)
- Pan Head Screws 2 x 8mm (60 Pieces)
- Drill Bits (Coated) 0.3/0.5/0.7mm (10 Each)
- Countersunk Screws 1 x 3mm (60 Pieces)
- Drill Bits (Coated) 0.3mm (10 Pack)
- Heavy Track Cutters
- Countersunk Screws 1 x 5mm (60 Pieces)
- Drill Bits (Coated) 0.5mm (10 Pack)
- Countersunk Screws 1 x 8mm (60 Pieces)
- Drill Bits (Coated) 0.7mm (10 Pack)
- Mitre Cutter Blade
- Countersunk Screws 1.5 x 4mm (60 Pieces)
- Countersunk Screws 1.5 x 6mm (60 Pieces)
- Mega Screw Set 16x 60 Vials (w/20 Drill Bit Set)
- Pan Head Screw Set 8x Vials with 60 screws in each